Matthews Studio Equipment

Made from Nylon Pack Cloth, these bags are ideal for storing Butterfly and Overhead Rags individually to keep them clean and not allow one wet rag to contaminate the others. The double drawstrings...

Both the Baby Pipe Clamp and the Junior Pipe Clamp have a uniquely designed hook molded into the clamp which keeps the clamp on the pipe even with a light fixture attached while the bolt is being...

Baby Grid Clamp: Made to clamp securely on overhead grids, car rigs, or camera car rails for mounting light fixtures. The Baby Grid Clamp can also be inverted with the pin mounting into a Grip Head...

Baby to 1/4-20" Male Adapter is used to allow devices with a 1/4-20 female thread to be mounted onto anything with a 5/8" Baby Pin. The Baby Pin is commonly used in the motion picture industry and...

To keep weight to a minimum and yet get maximum strength, all Matthews Solid Frames are made of 3/8" thin wall tubing. The mounting pin is solid rod. Matthews Solid Frames stainless steel for...

This 24'x24' reflector also has a yoke attached which terminates in a 5/8' receiver formounting on a Baby Stand. The 'soft' side has a stippled silver material, while the 'hard' side has the shiny...

Wall Spreaders are used in both vertical and horizontal positions. They are placed at each end of either a 2x4 or 2x6 precut piece of lumber. The Wall Spreader is a two piece system, one is simply a...

Matthews C Clamps are available in 4", 6", 8", 10" and 12" with or without 5/8" mounting pins or Junior Receivers. Each clamp has a steel channel welded to both sides of the opening for better and...

A "cheeseboro" clamp with a 1-1/8" pin attached to it serves multiple purposes. Use it with a piece of pipe with a diameter of 1-1/4" to 1-1/2" as a temporary overhead grid.

Virtually unbreakable when the ultimate in strength is required.Grips 1-1/4 to 1-1/2 inch pipe diameter.

Most film studios have very high ceilings and catwalks from which much of the lighting is done. Catwalks, also known as decks or greens, can be raised or lowered depending on the set. Catwalks have...

Roller Stands, or Overhead Stands as they are often called, utilize all steel tubes and legs. Developed for flying Butterflies and Overheads on location and supporting large backdrops in studios,...

Roller Stands, or Overhead Stands as they are often called, utilize all steel tubes and legs. Developed for flying Butterflies and Overheads on location and supporting large backdrops in studios,...

A Stand with an attitude! Wider footprint and longer legs provide increased stability. Complete with Rocky Mountain Leg and steel construction. Available with aluminum risers upon request. Will...

The K-Stacker II offers a simple solution for LED and FLO lighting support. Based on a concept from Canadian gaffer Alex Amyot, MSE has created a strong and robust tool that turns Kino Flo LED Panels...

Highlights Constructed from strong 6061 T6 aircraft grade aluminum Long mounting slots for adjustable plate balance position Rear cut out enables easy access to camera plate release Removable...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 4" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 6" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 8" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of...

OVERVIEW  MICROgrip Tabletop System Ideal for tabletop and product photography, this 12" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad...