OVERVIEW This July savings bundle comes with the 2 Quasar Science Q50XG Crossfade Lights and a T12 Double Q-Plate and Multi-Bank Power-2 Adapter for a scream deal! With the Quasar Science Q-LINE X Crossfade Linear LED Lamps (50 Watt), you can tune the...

Made from Nylon Pack Cloth, these bags are ideal for storing Butterfly and Overhead Rags individually to keep them clean and not allow one wet rag to contaminate the others. The double drawstrings pull through grommets for long wear. Custom size and...

Both the Baby Pipe Clamp and the Junior Pipe Clamp have a uniquely designed hook molded into the clamp which keeps the clamp on the pipe even with a light fixture attached while the bolt is being tightened. The Baby Pipe Clamp terminates in a 5/8 Pin...

Baby Grid Clamp: Made to clamp securely on overhead grids, car rigs, or camera car rails for mounting light fixtures. The Baby Grid Clamp can also be inverted with the pin mounting into a Grip Head for spanning pipe between two stands. Clamp will grip a...

Baby to 1/4-20" Male Adapter is used to allow devices with a 1/4-20 female thread to be mounted onto anything with a 5/8" Baby Pin. The Baby Pin is commonly used in the motion picture industry and can be found on everything including stands, rods,clips,...

This 24'x24' reflector also has a yoke attached which terminates in a 5/8' receiver formounting on a Baby Stand. The 'soft' side has a stippled silver material, while the 'hard' side has the shiny silver paper glued to it. Both boards weigh 6lbs.

Wall Spreaders are used in both vertical and horizontal positions. They are placed at each end of either a 2x4 or 2x6 precut piece of lumber. The Wall Spreader is a two piece system, one is simply a receptacle for the lumber with a padded flat plate...

Matthews C Clamps are available in 4", 6", 8", 10" and 12" with or without 5/8" mounting pins or Junior Receivers. Each clamp has a steel channel welded to both sides of the opening for better and safer locking. Clamps made for mounting Baby fixtures...

A "cheeseboro" clamp with a 1-1/8" pin attached to it serves multiple purposes. Use it with a piece of pipe with a diameter of 1-1/4" to 1-1/2" as a temporary overhead grid.

Virtually unbreakable when the ultimate in strength is required.Grips 1-1/4 to 1-1/2 inch pipe diameter.

Most film studios have very high ceilings and catwalks from which much of the lighting is done. Catwalks, also known as decks or greens, can be raised or lowered depending on the set. Catwalks have safety railings and there are usually holes drilled at...

Roller Stands, or Overhead Stands as they are often called, utilize all steel tubes and legs. Developed for flying Butterflies and Overheads on location and supporting large backdrops in studios, these stands feature wide bases for stability and...

A Stand with an attitude! Wider footprint and longer legs provide increased stability. Complete with Rocky Mountain Leg and steel construction. Available with aluminum risers upon request. Will accept Matthews #366066 Combo Adapter Wheels. Matthews...

The K-Stacker II offers a simple solution for LED and FLO lighting support. Based on a concept from Canadian gaffer Alex Amyot, MSE has created a strong and robust tool that turns Kino Flo LED Panels and Fluorescent Fixtures into larger, soft light...

Highlights Constructed from strong 6061 T6 aircraft grade aluminum Long mounting slots for adjustable plate balance position Rear cut out enables easy access to camera plate release Removable adaptor connects to Baby Pin or JR Receiver lighting stands...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 4" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of products that have been developed around the MICROgrip...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 6" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of products that have been developed around the MICROgrip...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 8" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of products that have been developed around the MICROgrip...

OVERVIEW  MICROgrip Tabletop System Ideal for tabletop and product photography, this 12" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of products that have been developed around the...

OVERVIEW MICROgrip Tabletop System Ideal for tabletop and product photography, this 20" MICROgrip 1/4"-20 Male to 1/4"-20 Female Rod from Matthews is part of a broad range of products that have been developed around the MICROgrip...