OVERVIEW Introducing our own Hot Rod Cameras Custom T12 Lamp Holder. Our Custom T8 lamp holders holds one fluorescent or quasar tube with a baby pin for mounting. This lamp holder features rubber covered clips and works very well with Quasar Science...

OVERVIEW Introducing our own Hot Rod Cameras Custom T8 Lamp Holder. Our Custom T8 lamp holders holds one fluorescent or quasar tube with a baby pin for mounting. This lamp holder features rubber covered clips and works very well with Quasar Science...

Overview Mount Tripod Head to Light Stand 1.7" Diameter Base with 3/8"-16 Screw Three Set Screws to Lock Down Head Interior Receptacle: 5/8" Exterior Diameter: 1-1/8" Easily mount a standard photo or video head to a light stand with this Baby Ball...

The AX1 Holder is an aluminum clamp that fits around and secures to the AX1 Pixel Tube. The holder secures with an included cotter pin.  The backside of the holder has a 1/4″ femaie thread for attaching to the AX1-BLT or similar. This can be...

DESIGNED WITH RUBBER COVERED CLIPS TO HOLD (1) FLUORESCENT T8 TUBE. TERMINATES IN A BABY (5/8) PIN. MADE FROM 6061 ALUMINUM. WORKS FOR QUASAR TUBES.

DESIGNED TO HOLD (2) T12 FLUORESCENT TUBES. TERMINATES IN A BABY (5/8) PIN. MADE FROM 6061 ALUMINUM. WORKS FOR BOTH KINO AND QUASAR TUBES.

Designed to mount a lighting fixture or accessories on to a baby swivel pin and can be angled in almost any direction. Has a ratcheted handle to allow for easy positioning and complete axis locking and unlocking.

Designed for holding a single Kino Flo fluorescent lamp/tube with double spring steel clips. Easily mounts into a grip head and can be positioned easily with the swivel ball joint design.

Both the Baby Pipe Clamp and the Junior Pipe Clamp have a uniquely designed hook molded into the clamp which keeps the clamp on the pipe even with a light fixture attached while the bolt is being tightened. The Baby Pipe Clamp terminates in a 5/8 Pin...

Baby Grid Clamp: Made to clamp securely on overhead grids, car rigs, or camera car rails for mounting light fixtures. The Baby Grid Clamp can also be inverted with the pin mounting into a Grip Head for spanning pipe between two stands. Clamp will grip a...

Baby to 1/4-20" Male Adapter is used to allow devices with a 1/4-20 female thread to be mounted onto anything with a 5/8" Baby Pin. The Baby Pin is commonly used in the motion picture industry and can be found on everything including stands, rods,clips,...

To keep weight to a minimum and yet get maximum strength, all Matthews Solid Frames are made of 3/8" thin wall tubing. The mounting pin is solid rod. Matthews Solid Frames stainless steel for durability. All Matthews Scrims and Flags are bordered with...

This 24'x24' reflector also has a yoke attached which terminates in a 5/8' receiver formounting on a Baby Stand. The 'soft' side has a stippled silver material, while the 'hard' side has the shiny silver paper glued to it. Both boards weigh 6lbs.

Wall Spreaders are used in both vertical and horizontal positions. They are placed at each end of either a 2x4 or 2x6 precut piece of lumber. The Wall Spreader is a two piece system, one is simply a receptacle for the lumber with a padded flat plate...

Matthews C Clamps are available in 4", 6", 8", 10" and 12" with or without 5/8" mounting pins or Junior Receivers. Each clamp has a steel channel welded to both sides of the opening for better and safer locking. Clamps made for mounting Baby fixtures...

A "cheeseboro" clamp with a 1-1/8" pin attached to it serves multiple purposes. Use it with a piece of pipe with a diameter of 1-1/4" to 1-1/2" as a temporary overhead grid.

Virtually unbreakable when the ultimate in strength is required.Grips 1-1/4 to 1-1/2 inch pipe diameter.

A Stand with an attitude! Wider footprint and longer legs provide increased stability. Complete with Rocky Mountain Leg and steel construction. Available with aluminum risers upon request. Will accept Matthews #366066 Combo Adapter Wheels. Matthews...

The 5/8" Baby Stud with 3/8"-16 Male Thread from Kupo can be used with a grip head or Super Clamp and attached to any accessory with female 3/8" threads, such as an articulating arm. Alternatively, the male threads can be mounted to a...

Measuring 3.5" in length, this 5/8" Baby Stud with 1/4"-20 Screw Mount from Kupo is a small accessory for a lighting grip kit. It offers a 1/4"-20 screw as its mounting point, allowing you to attach compact equipment such as LED...